DA21003L
Danuser SM40 Hammer | Post Driver | Universal Skid | Grapple | Tilt | Loaded
$10,835.00
Weight: 1245lbs
Unit Includes
- 96″ Hoses With FF Couplers
- Grapple
- Tilt
- Factory Installed Additional Weight Kit
Danuser Hammer
Model SM40 has a 40” drop hammer design with up to 35 strokes per minute. With this innovative design, you can achieve a full stroke with every cycle or utilize the short stroke feature to fine tune your depth. The Hammer DOES NOT operate with springs, hydraulic cylinder, or return line. Grapple option can be added to any model for a true one-person operation (does not include t-posts). The grapple option will allow the operator to grab the post off the ground, load it into the machine, and drive it in the ground without leaving the skid-steer seat. Tilt option allows up to 20˚ in each direction. The hammer weight is 300 lbs. from the factory. Additional weight can be added for a total of 500 lbs. The unit also has an integrated post puller to be used with log chain.
NOTE: If post/pipe diameter is 5″ or smaller and you have a helper, PN 21395 Donut Strike Plate must be purchased separately. If driving with one person, PN 21212 Horseshoe Strike Plate is a better option.
Unit Drives
- Fence Posts
- Sign Posts
- Guard Rails
- Median Dividers
- Tent Stakes
- T-Posts
- Pipe Fence
- Railroad Ties
| Post Dimensions: | T-post to RR Tie |
| Impact Force: | 82,000 lbs. |
| Length of Stroke: | 40 |
| Hammer Weight: | 300 |
| Strokes per Minute: | 35 |
| Model SM40 w/ Tilt | Model SM40 w/ Tilt and Grapple | |
| Overall Length | 45.5″ | |
| Overall Width | 25.5″ | |
| Overall Height | 64″ | |
| Tilt (side-side) | 20° | |
| Machine Weight | 1,005 lbs (1,205 lbs w/ additional weight) | 1,045 lbs (1,245 lbs w/ additional weight) |
| Hammer Weight | 300 LBS (500 LBS MAX) | |
| Length of Stroke | 40″ | |
| Max. Strokes per Minute | 35 | |
| Hydraulic Requirements | 1500-3000 PSI *12-30 GPM |
|
| Maximum Post Width | 8.5″ x 9.25″ | |
| Impact Force | 82,000 lbs @ 500 lb weight | |
| Impact Energy | 1,025 ft-lbs @300 lb weight; 1,709 ft-lbs @ 500 lb weight |
|
*Hammer will still operate on machines with less than 12 GPM with fewer strokes per minute.
Aux Wiring Harnesses
- Add An Optional Wiring Harness To Allow The Optional Tilt Function To Operate From The Vehicle Joystick Controls. Wiring Harnesses Replace The Cigarette Lighter Plug On The Hammer Standard Harness.
- Bobcat Has A 7-Pin Connector On Some Newer Skid Steer Units That Is Not Available Through Danuser, Contact Your Bobcat Dealer For A 7-Pin To 14-Pin Adapter
- All Wiring Harnesses Are 12″ In Length
- ** Requires Connector Contacts Be Installed In A Switchable +12V Pin Location & Ground Pin Location. Mapping Of Skid Steer Connector Pins Required.
Battery Wiring Harness
- Connect To Your Vehicle Battery To Supply Power For The Optional Tilt Function. This Replaces The Cigarette Lighter Plug On The Hammer Standard Harness.
| Weight | 1245 lbs |
|---|