Danuser T7 Hornet Post Driver | Backhoe/Ex | 10-30 GPM | Drives Up To 7″ Posts
PRICE DOES NOT INCLUDE SETUP OR SHIPPING – PRICED FOB FACTORY
*At Least 1 Driving Or Breaker Tool Must Be Added To Complete Unit
*Must Add Mount To Complete
*Hoses & Couplers Included
*Pictured With Optional Grapple
*Rated For Excavators 9,000 lb & Over
*Additional Weight Kit Not Available For Backhoe/Excavator Mounted Hornets
Danuser 214054 Hornet T7
- DA216003 Post Pulling / Depth Gauge 84″ Chain (Can Be Used For Pulling, Leveling & As A Depth Gauge)
- DA206101 Filled Nitrogen Bottle
- DA206102 Nitrogen Gas Charging Kit
- Drives T Posts – 7″ Diameter Posts
- Integrated Post Puller
- High Abrasion Resistant Hoses & Fittings With 1/2″ Flat Face Couplers
Danuser Hornet Post Drivers
• T-Posts • Tent Stakes • Pipe Fence • Sign Posts • Fence Posts • Railroad Ties • Median Dividers
- Jackhammer style power cell offers controlled high-speed driving performance.
- Hydraulic grapple option allows one person to pick up, load, & drive posts.
- Comes standard with a flow control valve. Our flow control valve allows us to run within a wider range of hydraulic requirements, including high flow machines, without accelerated wear on the breaker.
- Tool-less driving tool quick change which means no hammer and punch needed to change driving tools.
- Post holder with tie down locations for transporting posts/pipe.
- No setup required, it’s ready to go to work.
- 1-Year Warranty.
Advantages
- Hydraulic grapple option allows one person to pickup, load, & drive posts.
- Driving tools are made thicker & stronger. This helps to prevent breaking during excessive use.
- Tool-less driving tool quick change means no hammer & punch needed to change driving tools.
- The Hornet comes with a filled nitrogen bottle, N2 charge kit, & chain with hook.
- The flow control valve allows you to run within a wider range of hydraulic requirements, including high flow machines, without accelerated wear on the breaker.
- Post holder with tie down locations for transporting post/pipe when needed.
- High abrasion resistant hoses.
- T-Post adapter that can be used with flat or domed driving tool.
Nitrogen Charged Post Drivers
Jackhammer style post drivers have a chamber that holds a volume of nitrogen gas. The nitrogen is necessary for the post driver to perform the up and down stroke of the piston. The PSI of the nitrogen is critical to the operation of the driver. While a change in pressure can happen during dramatic seasonal changes, other than a routine pressure inspection, you should not need to do anything to the driver.
What Type Of Maintenance Is Required?
In addition to greasing the single grease zerk every two hours of use, checking the nitrogen pressure as the operator’s manual recommends. A thorough inspection of this or any attachment is always a good idea.
*Do not exceed the rated operating capacity of your vehicle. The addition of a Hornet adds up to 1,600 lb. of additional weight. Verify that the vehicle has sufficient lifting capacity, in each of the different vehicle positions. On Hornets with a grapple, the post weight will need to be considered as additional weight for lifting capacity considerations.
Hornet Driving Tools (At Least 1 Driving Tool Must Be Added To Complete The Hornet)
Domed Driving Tools – The domed driving tool is best for driving pipe or non-decorative wood posts as it can leave a beveled edge.
Flat Driving Tools – The flat driving tool is best for decorative wood posts.
Concrete Breaker Tools – The concrete breaker tool allows the Hornet to break rock & reinforced concrete. These tools have moil style points.
Aux Wiring Harnesses
Add An Optional Wiring Harness To Allow The Optional Tilt Function To Operate From The Vehicle Joystick Controls. Wiring Harnesses Replace The Cigarette Lighter Plug On T7 & T8-RR Standard Harness.
All Wiring Harnesses Are 12″ In Length
** Requires Connector Contacts Be Installed In A Switchable +12V Pin Location & Ground Pin Location. Mapping Of Backhoe/Excavator Connector Pins Required.
Battery Wiring Harness
Connect To Your Vehicle Battery To Supply Power For The Optional Tilt Function. This Replaces The Cigarette Lighter Plug On The T7 Or T8-RR Standard Harness.
Weight | 990 lbs |
---|