WL3P24
24″ PTO Stump Grinder | 25-55 HP | CAT I Or II | 540 RPM
$6,560.00
Weight: 880lbs
Baumalight 3P24 24″ PTO Stump Grinder | 25-55 HP | CAT I Or II | 540 RPM
*2 Hyd Remotes Required – The WLS1050 Must Be Added If Tractor Only Has One Set Of Remotes. Also, Recommended For Improved Feathering Control On Smaller Tractors, Valve Is Close Center.
3P24 Stump Grinder
The 3P24 PTO stump grinder is designed for tractors equipped with a 30–50 horse power motor allowing you to grind into stumps with a 24″ rotor carrying 34 replaceable carbide teeth. The cutting and lifting cylinders are powered by your tractor’s hydraulic remotes. Two remote hydraulics are required, if you only have one set then we offer a S1050 valve kit to ship with the stump grinder. The heavy duty base provides a solid base for grinding, reducing stress on the tractor. The flow control lets you set the optimal grinding sweep speed for the best efficiency. This versatile PTO Stump Grinder has a cutting depth of 18″ above ground and 8″ below ground. With direct drive from the engine, all the way through the heavy duty gear box to the teeth, a stump grinder on the PTO of a tractor is the most efficient way to use a stump grinder for lawn care or fence row clearing.
| Model No. | 1P24 | 3P24 | 3P34 | 3P40 |
|---|---|---|---|---|
| Recommended HP Size | 20-45 | 25-55 | 45-80 | 60-120 |
| Maximum Engine HP | 50 | 65 | 85 | 125 |
| Maximum PTO HP | 40 | 55 | 75 | 115 |
| Transmission | Hydrostatic only | Any | Any | Any |
| Hydraulic GPM | — | 5–20 | 5–20 | 5–20 |
| Rotor Size | 24″ | 24″ | 34″ | 34″ |
| Number of Teeth | 34 | 34 | 54 | 54 |
| Tooth Construction | Carbide steel bolt-in | Carbide steel bolt-in | Carbide steel bolt-in | Carbide steel bolt-in |
| Cutting Wheel Speed | 540 RPM | 810 RPM | 810 RPM | 1000 RPM |
| Cutting Height – Above Ground | 10″ | 18″ | 25″ | 25″ |
| Cutting Depth – Below Ground | 6″ | 8″ | 14″ | 14″ |
| Maximum Cutting Depth – Per Pass | 5″ | 6″ | 9″ | 9″ |
| Maximum Horizontal Cut | 22″ | 22″ | 32″ | 32″ |
| Swing Arc | 0° | 65° | 65° | 65° |
| Hub Torque | 803 Ft.-Lbs. | 803 Ft.-Lbs. | 803 Ft.-Lbs. | 1050 Ft.-Lbs. |
| Over Torque Protection | Slip clutch | Slip clutch | Slip clutch | Slip clutch |
| Hitch | Cat I | Cat I or II | Cat II | Cat II |
| No. of Remotes Required – Hydraulic | 0 | 1 or 2 | 1 or 2 | 1 or 2 |
| Requires 12 Volt DC | No | No | No | No |
| Input Speed | 540 | 540 | 540 | 1000 |
| Unit Weight (Shipping) Lbs. | 350 | 920 | 1231 | 1280 |
| Width (Shipping) | 48″ | 42″ | 48″ | 48″ |
| Length (Shipping) | 48″ | 49″ | 54″ | 54″ |
FLOW CONTROL
Fine tune the performance of your Stump Blaster easily with the Flow Control knob. The Flow Control allows you to adjust the cutting pass speed, to match the size and performance of your tractor. This gives you the smoothest cut possible and with the full return back to the start position, the quickest overall stump grinding time possible.
GEARBOX
The rugged gear box transfers power from the tractor’s PTO to the rotor creating 803 Ft.-Lbs of torque and turning the rotor and hungry teeth at 810 RPM.
CARBIDE TIPPED
Like the finest saw blades, the cutting teeth on Stump Blasters are carbide tipped. This incredibly hard material ensures reliable cutting performance. When grinding stumps, buried hazards are inevitable; gravel, stones even metal posts are not uncommon to “find”. Our carbide teeth are designed to stand up to this abuse and keep on blasting stumps to dust.
MORE TEETH
Many hands make light work, or in this case fine mulch faster and easier. The high number of teeth means that each tooth does less work. Each of the Stump Blasters teeth only need to make a small cut, because the work is shared by more of these rugged teeth, which last longer and typically only need 2 or 3 replaced at a time. The bolt-on designed teeth allow for straightforward replacement.
ROTOR
The massive ¾” thick steel rotor provides the back bone for the Stump Blaster cutting system. It’s the anchor for the carbide tipped teeth. For smooth operation it’s important that the rotor remains solid, with no flexing. The rugged rotor also provides the Stump Blaster with the extra momentum needed when the grinding is tough, making sure the Stump Blaster can power through the hardest stumps.
MORE CLEARANCE
The Stump Blaster’s carbide teeth extend a full 1-¼ inches from the rotor. This prevents chips and mulch from getting plugged. More chip clearing produces smoother operation and reduces heat build-up that can damage the rotor and cause premature tooth failure.
STABILIZER BASE
The heavy duty base provides a solid base for grinding. This allows for more consistent grinding performance and reduces the stress on your tractor.
FLOATING DEFLECTOR
The deflector floats as you grind providing chip and debris control from first cut to maximum depth without getting in the way. In tight grinding situations the deflector can be flipped up out of the way.
SWING & LIFT CYLINDERS
Get right to grinding with less maneuvering of your tractor and less damage to the grass. The swing cylinder gives the operator a 65 degree grinding range without moving the tractor. The lift cylinder allows you to raise and lower the grinding head to get in start position as well as lowering the head after a pass so you’re ready for the next bite.
HARDENED STEEL BUSHING
Spring Bushings made from high grade chrome-vanadium AISI 6150 spring steel on all main pivot points.
GREASEABLE PINS
Our grease pins are zinc plated to prevent corrosion which will allow for smoother operation of the units joints over their lifetime.
______________________________________________________________________________________________________________________________________________________________________________________________________
PRICE DOES NOT INCLUDE SETUP OR SHIPPING – PRICED FOB FACTORY
| Weight | 880 lbs |
|---|