FBS752 Feller Buncher | Univ Skid | 52″ Dia Blade | 20″ Max Cut | T590 Motor 30-45 GPM

PRICE DOES NOT INCLUDE SETUP OR SHIPPING – PRICED FOB BV ATWOOD, KS

*Requires Case Drain (See Tab Below For Info On Case Drains)

*Hydraulic Hoses Included – NO Couplers (See Tab Below To Add Hyd Couplers)

*The FBS752 Comes With Baumalight’s Auxiliary Electrical Connection. Required Live Pins – 4 Hot On AUX (Wire With Pin Supplied To AUX On Boom) | When Ordering Unit, Please Note What Model Of Skid Steer It Is Going On & The Pin Connection. Baumalight Will Equip The Unit With Your Skid Steer’s Specific Auxiliary Connection Prior To Shipment.

A Control Box Kit Must Be Added If –
- Your Skid Steer Is Older And Does Not Have An Auxiliary Electrical Connection

*Do You Have A Newer Bobcat Skid Steer With A Specific Bobcat 7-Pin Connector?

To Run This Unit With Your Skid Steer, You Will Either Have To Add The Control Box Kit, Add The Bobcat 7-Pin CANBUS Plug/Circuit Board Kit, Or Contact Your Bobcat Dealer For A 7-Pin To 14-Pin Adapter.

Feller Buncher For Skid Steer

The FBS752 Skidsteer Mounted Feller Buncher we designed features a 52” cutting disc that can take up to 20” trees and is equipped with 18 Beaver cutting teeth. The tower is build with 4×4 tubing to allow more visibility for the operator and high stress areas use AR400 steel for added strength.

It has an electric-over-hydraulic system which operates efficiently on hydraulic flows as little as 25 gpm and is powered by a bent axis piston motor. Only one set of remote hydraulics is required to operate all functions if you have an AUX electrical connection.

FBS752	FBXH752	FBXP752	FBXD752
–	A03	A03	A03
Skidsteer Mounted	Excavator Mounted	Excavator Mounted	Excavator Mounted
Fixed Horizontal Blade	Fixed Horizontal Blade	90° Pivot Blade	360° Slew drive
Universal Skidsteer Adaptor	Bolt-on Adaptor	Bolt-on Adaptor Cylinder Actuator	Bolt-on Adaptor Slew Drive
4000 PSI	4000 PSI	4000 PSI	4000 PSI
Requires 12V Electric	Requires 12V Electric	Requires 12V Electric	Requires 12V Electric
Four 12V positive switchable signals required	Four 12V positive switchable signals required	Six 12V positive switchable signals required	Six 12V positive switchable signals required
Wire Supplied to AUX	Wire NOT Supplied	Wire NOT Supplied	Wire NOT Supplied
Hoses Included Couplers NOT Included	Hoses & Couplers NOT Included	Hoses & Couplers NOT Included	Hoses & Couplers NOT Included
52″ Diameter Blade	52″ Diameter Blade	52″ Diameter Blade	52″ Diameter Blade
20″ Max Cut	20″ Max Cut	20″ Max Cut	20″ Max Cut
1″ Steel Blade	1″ Steel Blade	1″ Steel Blade	1″ Steel Blade
1 5/8″ Cutt Thickness	1 5/8″ Cutt Thickness	1 5/8″ Cutt Thickness	1 5/8″ Cutt Thickness
4 Edges Per Tooth	4 Edges Per Tooth	4 Edges Per Tooth	4 Edges Per Tooth
18 Teeth	18 Teeth	18 Teeth	18 Teeth
B8000 Beaver Teeth	B8000 Beaver Teeth	B8000 Beaver Teeth	B8000 Beaver Teeth
Throat Opening at teeth: 36″	36″ Throat Opening	36″ Throat Opening	36″ Throat Opening

Feller Bunchers

The first Skidsteer Mounted Feller Buncher we designed features a 52” cutting disc that can take up to 20” trees and is equipped with 18 Beaver cutting teeth from Quadco.The Quadco teeth are made from high-grade alloy steel, heat treated to a high Rockwell rating, while not being brittle. The Beaver style, with its straight edges, is much more durable than the Concave and keeps a better cutting edge longer. Tips can be re-sharpened right on the blade with a teeth grinder. Holders and teeth are fully rotatable and reversible. This will double the life of the tooth, reduce operating costs, as you double your tips for less than 1/3 more. Our first model also has an accumulator arm is included to cut and carry multiple smaller trees before discharging them to the pile. It has an electric-over-hydraulic system which operates efficiently on hydraulic flows as little as 25gpm and a smaller model would work on lower flow yet. Only one set of remote hydraulics is required to operate all functions if you have an AUX electrical connection. We are very open to requests for new features, larger or smaller models.

Only one set of remote hydraulics is required to operate all functions if you have an AUX electrical connection, and a case drain is required.

36″ Throat Opening

The Feller Buncher has a 36″ wide throat opening at the teeth. This allows you to do a nice low cut on trees with a wide root flair.

What Is A Case Drain Line ?

On most skidsteer and excavator Hydraulic systems, Hydraulic motors and pumps require a case drain line. Sometimes referred to as a third line, the case drain line will relieve any excess pressure and drain it back to your return line, then into the reservoir. Without a properly installed case drain, that extra pressure could blow a seal or damage your hydraulic line. For higher flow motors or on piston and gear motors, a case drain line is always required. Although, no matter the size of your motor, a case drain is always a good idea as it will relieve the amount of pressure on your shaft seal, helping to prolong its life. A case drain line can also increase the efficiency of your hydraulic system as it will lower the back pressure on the tank line.

Since most machines have a unique style of coupler, BaumaLight does not include a coupler on our case drain line, although they are available. If your skidsteer is not equipped with a case drain, then it can be field installed.

How Important Is A Case Drain Line ?

If we say having a case drain is critical and you operate without one, you will blow out your shaft seal. Be sure to check the motor sizing charts on our website.

Exception If You Have A Hammer Valve

There is one exception in the need for a case drain on gear motors and that is if you excavator is equipped with a hammer valve, this is a larger free flow line back to tank.

Identifying Your Case Drain Line

The following galleries show a highlighted case drain line on multiple skidsteer and excavator models.

Controls Overview

Name: WLFBS752-T590
SKU: 49868
Price: 29650.00 USD
Availability: InStock

Auxiliary Connection (Included Standard)

*If you have a newer skid steer with auxiliary connection, please note what model of skid steer it is going on & the pin connection. Baumalight will equip the unit with your skid steer’s specific auxiliary connection prior to shipment. This Is The Ideal Solution. The operator can easily control all functions using the controls already equipped on the carrier joysticks. This allows the operator to never remove their hands from the controls to change a function.

Wired Control Box (Optional)

*If your skid steer is older & does not have an auxiliary electrical connection, you must add the WLD004956 wired control box. Although less than ideal, for controlling the attachment is using our wired control box. The operator would use the toggle switches on the control box to control the functions required. The wired control box requires a 12V connection to supply power.

WLD004956

Wired Control Box For FBS752 | Plugs Into 14 Pin Plug $396.00

Add to List

Do You Have A Newer Bobcat Skid Steer With A Specific Bobcat 7-Pin Connector?

-If so, you will either have to add the control box kit, the Bobcat 7-pin CANBUS plug/circuit board kit, or contact your Bobcat dealer for a 7-pin to 14-pin adapter.