WLMX1160R-D117X2
Baumalight MX1160R 90″ Brush Mulcher | Ex Mount | 18-33 Ton Carriers | Adj D117X2 Mtr 20-75 GPM
$32,400.00
Weight: 2925lbs
MX1160R Heavy Duty Fixed Tooth Mulcher for Excavator, 18 to 33 Ton
The Baumalight MX1160R Brush Mulcher has a 60” rotor and is designed for excavators up to 33 tons. The MX1160R comes with unique performance boosting mulcher rings (licensed by Denis Cimaf). These rings improve the speed and efficiency of your mulching while reducing the risk of breakage on the tooth holders by limiting the size of the bites.
The MX1160R uses a fixed tooth holder and comes with 31 sharpenable planer teeth (P11000), as you will see in the brush cutting size charts this allow mulching of much larger material with an average carrier. The MX1160R comes with aggressive root rake ripper teeth build into the frame to rip out rocks and move logs. The unit also has a heavier duty body, built with a low-weight, high-strength AR400 steel.
| Model No. | MX230 | MX330 | MX530 | MX530R | MX548 | MX548R | MX948R | MX960R | MX1160R |
|---|---|---|---|---|---|---|---|---|---|
| Baumalight Connection Code | A02 | A02 | A02 | A02 | A03 | A03 | A03 | A03 | A03 |
| Path Width | 38″ | 38″ | 40″ | 40″ | 62″ | 62″ | 70″ | 90″ | 90″ |
| Rotor Width | 30″ | 30″ | 30″ | 30″ | 48″ | 48″ | 48″ | 60″ | 60″ |
| Maximum Carrier Ton | 6 | 8 | 12 | 12 | 20 | 20 | 30 | 33 | 33 |
| Minimum Carrier Ton | 2 | 3 | 4 | 4 | 8 | 8 | 12 | 18 | 18 |
| Cutting Depth | Level | Level | 1.5″ Above to 1″ Below Grade | 1.5″ Above to 1″ Below Grade | 1.5″ Above to 1″ Below Grade | 1.5″ Above to 1″ Below Grade | Level | Standard level – Optional skid shoes for below ground | Standard level – Optional skid shoes for below ground |
| Holder Style | Swing | Fixed | Fixed | Fixed | Fixed | Fixed | Fixed | Fixed | Fixed |
| Cutting Style | Flall | High Speed Teeth | Carbide Tipped Bolt In | Carbide Tipped Bolt In | Carbide Tipped Bolt In | Carbide Tipped Bolt In | Double Tipped Carbide | Double Tipped Carbide | Sharpenable Planer teeth |
| Number of Cutters | 22 | 36 | 64 | 64 | 104 | 104 | 27 | 38 | 31 |
| Rotor Shaft Size | 1.5″ | 2″ | 2″ | 2″ | 2″ | 2″ | 2″ | 2″ | 2″ |
| Rotor Diameter (tool tips) | 17.25″ | 15″ | 15″ | 15″ | 15″ | 15″ | 18.5″ | 18.5″ | 18.5″ |
| Rotor Weight (with tools) | 125 lbs | 175 lbs | 300 lbs | 300 lbs | 408 lbs | 408 lbs | 617 lbs | 860 lbs | 872 lbs |
| No. of Motor | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 |
| System Protection | Built-In Rellef | Built-In Rellef | Built-In Rellef | Built-In Rellef | Built-In Rellef | Built-In Rellef | Built-In Rellef | Built-In Rellef | Built-In Rellef |
| Unit Weight | 500 lbs | 750 lbs | 1036 lbs | 1166 lbs | 2167 lbs | 2167 lbs | 2838 lbs | 2910 lbs | 2925 lbs |
MAXIMUM BRUSH CUTTING SIZES
(Brush Diameter in Inches)
500 Series
| MOTOR | PSI | CASE DRAIN | 8 GPM |
12 GPM |
15 GPM |
20 GPM |
25 GPM |
30 GPM |
35 GPM |
40 GPM |
45 GPM |
50 GPM |
55 GPM |
60 GPM |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| RPM | 555 | 832 | 1060 | 1390 | ||||||||||
| A450 Roller-Vane | 2500 3000 3500 |
Not Needed Not Needed Recommended |
0.25″ 0.5″ 0.5″ |
0.75″ 1″ 1″ |
1″ 1.25″ 1.25″ |
1.5″ 2″ 2″ |
— — — |
— — — |
— — — |
— — — |
— — — |
— — — |
— — — |
— — — |
| RPM | 640 | 846 | 1100 | 1370 | 1600 | |||||||||
| B550 Roller-Vane | 2500 3000 3500 |
Not Needed Recommended Needed |
— — — |
0.25″ 0.5″ 0.5″ |
0.75″ 1″ 1″ |
1.25″ 1.75″ 1.75″ |
2.5″ 3″ 3″ |
3″ 3.5″ 3.5″ |
— — — |
— — — |
— — — |
— — — |
— — — |
— — — |
| RPM | 1090 | 1640 | 2050 | |||||||||||
| C508 Bent Axis Piston | 2500 3000 3500 4000 |
Critical | 1″ 1.5″ 2″ 2.5″ |
1.75″ 2.25″ 2.75″ 3.25″ |
2.25″ 2.75″ 3.25″ 4″ |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
| RPM | 1190 | 1490 | 2000 | 2490 | ||||||||||
| C510 Bent Axis Piston | 2500 3000 3500 4000 |
Critical | — — — — |
1.5″ 2″ 2.5″ 3″ |
2″ 2.5″ 3″ 3.5″ |
2.5″ 3″ 3.5″ 4.5″ |
3″ 3.5″ 4.5″ 5″ |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
| RPM | 1450 | 1800 | 2100 | |||||||||||
| C530 Bent Axis Piston | 2500 3000 3500 4000 |
Critical | — — — — |
— — — — |
— — — — |
2.5″ 3″ 3.5″ 4.5″ |
3.5″ 4″ 4.5″ 5″ |
4.5″ 5″ 5.5″ 5.75″ |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
| RPM | 1500 | 1800 | 2100 | |||||||||||
| C540 Bent Axis Piston | 2500 3000 3500 4000 |
Critical | — — — — |
— — — — |
— — — — |
— — — — |
3.25″ 3.75″ 4.25″ 4.75″ |
5″ 5.5″ 5.75″ 6″ |
5.5″ 6″ 6.5″ 7″ |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
| RPM | 1600 | 1875 | 2140 | |||||||||||
| C550 Bent Axis Piston | 2500 3000 3500 4000 |
Critical | — — — — |
— — — — |
— — — — |
— — — — |
— — — — |
4.5″ 5″ 5.5″ 5.75″ |
6″ 6.5″ 7″ 7.5″ |
6.5″ 7″ 7.5″ 8″ |
— — — — |
— — — — |
— — — — |
— — — — |
| RPM | 1400 | 1630 | 1830 | 2030 | ||||||||||
| C570 Bent Axis Piston | 2500 3000 3500 4000 |
Critical | — — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
5.5″ 6″ 6.5″ 7″ |
5″ 5.5″ 6″ 6.5″ |
6.5″ 7″ 7.5″ 8″ |
7″ 7.5″ 8″ 8.5″ |
— — — |
— — — |
| RPM | 1400 | 1570 | 1750 | 1900 | ||||||||||
| C590 Bent Axis Piston | 2500 3000 3500 4000 |
Critical | — — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
4.5″ 5″ 5.5″ 6″ |
7″ 7.5″ 8″ 9″ |
8.5″ 9″ 9.5″ 10″ |
9″ 9.5″ 10″ 11″ |
Double brush size for “stop and chew” cutting for skidsteer models ONLY
NOTICE: Max GPM value must NEVER be exceeded on roller-vane motors or failure will occur, Piston motors run much faster before failure will occur
NOTICE: Above GPM values are under load flow estimates
900 Series
| MOTOR | PSI | CASE DRAIN | 20 GPM |
25 GPM |
30 GPM |
35 GPM |
40 GPM |
45 GPM |
50 GPM |
55 GPM |
60 GPM |
65 GPM |
70 GPM |
75 GPM |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| RPM | 1450 | 1800 | 2100 | |||||||||||
| C930 Bent Axis Piston |
2500 3000 3500 4000 |
Critical | 3.5″ 4″ 4.5″ 5.5″ |
4.5″ 5″ 5.5″ 6″ |
5.5″ 6″ 6.5″ 7″ |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
| RPM | 1500 | 1800 | 2100 | |||||||||||
| C940 Bent Axis Piston |
2500 3000 3500 4000 |
Critical | — — — — |
4.25″ 4.75″ 5.25″ 5.75″ |
6.25″ 6.5″ 6.75″ 7″ |
6.5″ 7″ 7.5″ 8″ |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
| RPM | 1600 | 1875 | 2140 | |||||||||||
| C950 Bent Axis Piston |
2500 3000 3500 4000 |
Critical | — — — — |
— — — — |
5.5″ 6″ 6.5″ 6.75″ |
7″ 7.5″ 8″ 8.5″ |
7.5″ 8″ 8.5″ 9″ |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
| RPM | 1400 | 1630 | 1830 | 2030 | ||||||||||
| C970 Bent Axis Piston |
2500 3000 3500 4000 |
Critical | — — — — |
— — — — |
— — — — |
5.5″ 6″ 7.5″ 8″ |
6″ 6.5″ 7″ 7.5″ |
7.5″ 8″ 8.5″ 9″ |
8″ 8.5″ 9″ 9.5″ |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
| RPM | 1400 | 1570 | 1750 | 1900 | ||||||||||
| C990 Bent Axis Piston |
3000 3500 4000 |
Critical | — — — — |
— — — — |
— — — — |
— — — — |
— — — — |
6″ 6.5″ 7″ |
8.5″ 9″ 10″ |
10″ 10.5″ 11″ |
10.5″ 11″ 12″ |
— — — — |
— — — — |
— — — — |
| RPM | Adjustable | |||||||||||||
| D97X2 Two speed (900 series) |
2500 3000 3500 4000 |
Critical | 4.25″ 5″ 5.5″ 6.75″ |
5.5″ 6.25″ 6.75″ 7.5″ |
7.75″ 8″ 8.5″ 8.75″ |
8.75″ 9.25″ 10″ 10.5″ |
9.25″ 10″ 10.5″ 11.25″ |
10.25″ 11″ 11.5″ 12.25″ |
11.25″ 12″ 12.5″ 13.25″ |
12.25″ 13″ 13.5″ 14.25″ |
13.25″ 14″ 14.5″ 15.25″ |
14.25″ 15″ 15.5″ 16.25″ |
15.25″ 16″ 16.5″ 17.25″ |
16.25″ 17″ 17.5″ 18.25″ |
Double brush size for “stop and chew” cutting for skidsteer models ONLY
NOTICE: Max GPM value must NEVER be exceeded on roller-vane motors or failure will occur, Piston motors run much faster before failure will occur
NOTICE: Above GPM values are under load flow estimates
1100 Series
| MOTOR | PSI | CASE DRAIN | 20 GPM |
25 GPM |
30 GPM |
35 GPM |
40 GPM |
45 GPM |
50 GPM |
55 GPM |
60 GPM |
65 GPM |
70 GPM |
75 GPM |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| RPM | 1450 | 1800 | 2100 | |||||||||||
| C1130 Bent Axis Piston |
2500 3000 3500 4000 |
Critical | 4.5″ 5″ 5.5″ 6.5″ |
5.5″ 6″ 6.5″ 7″ |
6.5″ 7″ 7.5″ 8″ |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
| RPM | 1500 | 1800 | 2100 | |||||||||||
| C1140 Bent Axis Piston |
2500 3000 3500 4000 |
Critical | — — — — |
6.25″ 6.75″ 7.25″ 7.75″ |
8.25″ 8.5″ 8.75″ 9″ |
8.5″ 9″ 9.5″ 10″ |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
| RPM | 1600 | 1875 | 2140 | |||||||||||
| C1150 Bent Axis Piston |
2500 3000 3500 4000 |
Critical | — — — — |
— — — — |
8.5″ 9″ 9.5″ 9.75″ |
10″ 10.5″ 11″ 11.5″ |
10.5″ 11″ 11.5″ 12″ |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
| RPM | 1400 | 1630 | 1830 | 2030 | ||||||||||
| C1170 Bent Axis Piston |
2500 3000 3500 4000 |
Critical | — — — — |
— — — — |
— — — — |
9.5″ 10″ 11.5″ 12″ |
10″ 10.5″ 11″ 11.5″ |
11.5″ 12″ 12.5″ 13″ |
12″ 12.5″ 13″ 13.5″ |
— — — — |
— — — — |
— — — — |
— — — — |
— — — — |
| RPM | 1400 | 1570 | 1750 | 1900 | ||||||||||
| C1190 Bent Axis Piston |
2500 3000 3500 4000 |
Critical | — — — — |
— — — — |
— — — — |
— — — — |
— — — — |
10″ 10.5″ 11″ 11.5″ |
12.5″ 13″ 13.5″ 14.5″ |
14″ 14.5″ 15″ 15.5″ |
14.5″ 15″ 15.5″ 16.5″ |
— — — — |
— — — — |
— — — — |
| RPM | Adjustable | |||||||||||||
| D117X2 Two speed |
2500 3000 3500 4000 |
Critical | 5.5″ 6.25″ 6.75″ 8″ |
7.75″ 8.25″ 9″ 9.5″ |
10.5″ 11.25″ 11.5″ 12″ |
12.5″ 13″ 13.5″ 14.25″ |
13″ 13.75″ 14.25″ 15″ |
14.25″ 15″ 15.5″ 16.25″ |
15.5″ 16.25″ 16.75″ 18″ |
17.5″ 18″ 18.75″ 19.25″ |
18″ 18.75″ 19.25″ 20.5″ |
19″ 19.75″ 20.25″ 21.5″ |
20″ 20.75″ 21.25″ 22.5″ |
21″ 21.75″ 22.25″ 23.5″ |
Double brush size for “stop and chew” cutting for skidsteer models ONLY
NOTICE: Max GPM value must NEVER be exceeded on roller-vane motors or failure will occur, Piston motors run much faster before failure will occur
NOTICE: Above GPM values are under load flow estimates
REPLACEABLE BOLT-IN LINER
Save time by easily replacing the AR400 steel wear plates on the MX960R without needing to remove the rotor.
ADJUSTABLE BELT TENSIONER
The adjustable belt tensioner ensures the proper tension of your belts, with no extra idler wheel that could wear out. Simply loosen the bolts and raise the motor mount to tighten the belt.
BENT AXIS PISTON MOTORS ARE A STANDARD OPTION
Our industry leading bent axis piston motors make the most use of your hydraulic flow and pressure for your brush clearing needs.
WIRE PROTECTION KIT
If you are mulching and you catch some old fence wire, it can really cause damage to the unit if the wire slips over the edge of the rotor and gets wrapped around the shaft. The wire can get bunched against the bearings, causing major damage. Our wire protection kit contains a welded raised area on the end of the rotor that protects the shaft and prevents wire from getting in.
CHAIN CURTAIN
The rear of the unit is guarded by a chain curtain so standing brush enters and mulched debris exits.
6 FREE TEETH
All MX960R Brush Mulchers come with a free set of 6 replacement teeth. These replacement teeth can be convenienty stored in the enclosed spare tool compartment.
EASY ACCESS GREASE FITTINGS
Reduce your regular maintenance time by easily greasing the bearings on the MX960R from outside the frame. No tools required.
OVERTORQUE PROTECTION – RELIEF VALVE
The relief valve protects the motor and the hydraulic system from pressure spikes. When an obstacle is hit the relief valves open and relieves the pressure.
REINFORCED BELT
A heavy duty reinforced belt delivers the force from the gear box to the rotor. This offers protection from the shocks inherent in mulching.
What Is A Case Drain Line ?
On most skidsteer and excavator Hydraulic systems, Hydraulic motors and pumps require a case drain line. Sometimes referred to as a third line, the case drain line will relieve any excess pressure and drain it back to your return line, then into the reservoir. Without a properly installed case drain, that extra pressure could blow a seal or damage your hydraulic line. For higher flow motors or on piston and gear motors, a case drain line is always required. Although, no matter the size of your motor, a case drain is always a good idea as it will relieve the amount of pressure on your shaft seal, helping to prolong its life. A case drain line can also increase the efficiency of your hydraulic system as it will lower the back pressure on the tank line.
Since most machines have a unique style of coupler, BaumaLight does not include a coupler on our case drain line, although they are available. If your skidsteer is not equipped with a case drain, then it can be field installed.
How Important Is A Case Drain Line ?
If we say having a case drain is critical and you operate without one, you will blow out your shaft seal. Be sure to check the motor sizing charts on our website.
Exception If You Have A Hammer Valve
There is one exception in the need for a case drain on gear motors and that is if you excavator is equipped with a hammer valve, this is a larger free flow line back to tank.
Identifying Your Case Drain Line
The following galleries show a highlighted case drain line on multiple skidsteer and excavator models.
Excavator Mounting
Baumalight offers two options to mount your attachment on your excavator, blank weld-on plates & turn key custom solutions. All Baumalight excavator mounting options are manufactured in Canada and our team of experts will work with you to ensure you receive the best solution for your excavator.
Blank Weld-On Plates
The bank weld-on plate is designed for you to weld on your own ear lugs for your specific excavator mount. The bolt pattern in the plate lines up with the bolt pattern on Baumalight attachments, allowing you to bolt the attachment in place.
Turn-Key Custom Solutions
A fully customized solution, the team at Baumalight designs and builds your custom excavator adaptor for your specific excavator to ensure that the attachment is ready to go to work as soon as it arrives.
Add Connection Code
Click The Link Below To Find Your Specific D00**** Ex Mount
Add Turn Key Option That Corresponds With Your D00****
Please Note Your D00**** When Ordering
The Turn Key Pricing Includes The Connection Code Price
| Weight | 2925 lbs |
|---|