S18 Stump Grinder | 25-80 HP | 12-22 GPM | S450 Mtr | Less Mount
Hydraulic Couplers Included
No Case Drain Required
Self Regulated In-Feed
Must Add Mount To Complete – See Below
Skid Steer Specs
Model No. | S14 | S18 | S24 | S28 | S40 |
---|---|---|---|---|---|
Recommended HP Size | 12-30 | 25-80 | 30-80 | 50-120 | 50-120 |
Maximum Carrier Size | Check GPM & PSI | Check GPM & PSI | Check GPM & PSI | Check GPM & PSI | Check GPM & PSI |
Motor Type | Gerotor | Gerotor | Gerotor | Gerotor | Bent Axis Piston |
Hydraulic GPM | Check Stump Cutting Size Chart | Check Stump Cutting Size Chart | Check Stump Cutting Size Chart | Check Stump Cutting Size Chart | Check Stump Cutting Size Chart |
Rotor Size | 18″ | 24″ | 24″ | 24″ | 24″ |
Number of Teeth | 12 | 34 | 34 | 34 | 20 |
Tooth Construction | Wearsharp® | Planer | Planer | Planer | Wearsharp® |
Cutting Wheel Speed | Depends on GPM | Depends on GPM | Depends on GPM | Depends on GPM | Depends on GPM |
Cutting Height – Above Ground | No limit | No limit | No limit | No limit | No limit |
Cutting Depth – Below Ground | 6″ | 10″ | 10″ | 10″ | 24″ |
Maximum Cutting Depth – Per Pass | 2″ | 5″ | 6″ | 6″ | 1″ |
Maximum Horizontal Cut | 12″ | 22″ | 22″ | 22″ | 22″ |
Swing Arc | Self-feeding | Self-feeding | 80° | 80° | 85° |
Hub Torque | 150 Ft.-Lbs. | 250 Ft.-Lbs. | 250 Ft.-Lbs. | 803 Ft.-Lbs. | – |
Over Torque Protection | Relieve valve | Relieve valve | Relieve valve | Relieve valve | Remote |
Hitch | 1″ pivot pins | 1″ pivot pins | Quick Attach | Quick Attach | Quick Attach |
No. of Remotes Required – Hydraulic | 1 | 1 | 1 | 1 | 1 |
Requires 12 Volt DC | No | No | Yes | Yes | Yes |
Unit Weight (Shipping) Lbs. | 394 | 642 | 995 | 995 | 1,200 |
Excavator Specs
Model No. | S14 | S18 | GXM350 | GXM550 | GXM750 |
---|---|---|---|---|---|
Baumalight Connection Code | A04 | A04 | A02 | A02 | A02 |
Recommended Carrier Size | 1-2 ton | 1.5-4 ton | 1.5-4.5 ton | 3.5-8 ton | 7-18 ton |
Motor Type | Gerotor | Gerotor | High efficiency bent axis piston | High efficiency bent axis piston | High efficiency bent axis piston |
Hydraulic GPM | Check Motor Options | Check Motor Options | Check Motor Options | Check Motor Options | Check Motor Options |
Rotor Size | 18″ | 24″ | 19″ | 24″ | 24″ |
Number of Teeth | 12 | 34 | 16 | 20 | 20 |
Tooth Construction | Wearsharp® | Planer | Wearsharp® | Wearsharp® | Wearsharp® |
Cutting Wheel Speed | Depends on GPM | Depends on GPM | Depends on GPM | Depends on GPM | Depends on GPM |
Cutting Height – Above Ground | No limit | No limit | No limit | No limit | No limit |
Cutting Depth – Below Ground | 6″ | 10″ | 16″ | 24″ | 24″ |
Maximum Cutting Depth – Per Pass | 2″ | 5″ | 3/4″ | 1″ | 1″ |
Maximum Horizontal Cut | 12″ | 22″ | 12″ | 22″ | 22″ |
Over Torque Protection | Relieve valve | Relieve valve | Relieve valve | Relieve valve | Relieve valve |
Hitch | 1″ pivot pins | 1″ pivot pins | Bolt on | Bolt on | Bolt on |
No. of Remotes Required – Hydraulic | 1 | 1 | 1 | 1 | 1 |
Requires 12 Volt DC | No | No | No | No | No |
Unit Weight (Shipping) Lbs. | 394 | 642 | 650 | 822 | 1300 |
WEARSHARP® TEETH
By Green Manufacturing, Inc.
The unique design of the Wearsharp® allows the tooth to retain a sharp cutting surface, unlike traditional teeth that tend to round over. This provides a consistent cut throughout the life of the tooth, allowing you to maintain a faster sweep speed. This round tooth is 3 teeth in 1. Simply loosen the lock nut and rotate the tooth to a fresh, sharp cutting edge. This can be done three times, extending the life of each tooth.
MORE TEETH
The high number of teeth means that each tooth needs to do less work. Each of the Stump Blasters teeth only need to make a small cut, because the work is shared by more of our rugged teeth they last longer and usually only require 2 or 3 replacements at a time. The bolt-on designed teeth allow for straightforward replacement.
HYDRAULIC MOTOR
Skid steer mounted Stump Blasters run on hydraulic motors. For best results, match your equipments flow rate to one of our available hydraulic motor options.
MORE CLEARANCE
The Stump Blaster’s carbide teeth extend a full 1-¼ inches from the rotor. This prevents chips and mulch from getting plugged. More chip clearing produces smoother operation and reduces heat build-up that can damage the rotor and cause premature tooth failure.
ROTOR
The massive ¾” thick steel rotor provides the back bone for the Stump Blaster cutting system. It’s the anchor for the carbide tipped teeth. For smooth operation it’s important that the rotor remains solid, with no flexing. The rugged rotor also provides the Stump Blaster with the extra momentum needed when the grinding is tough, making sure the Stump Blaster can power through the hardest stumps.
GREASEABLE PINS
Our grease pins are zinc plated to prevent corrosion which will allow for smoother operation of the units joints over their lifetime.
WLD001126 | S14 & S18 Mini Skid Attachment |
WLD001127 | S14 & S18 Skid Steer Attachment Universal |
WLD001943 | S14 & S18 Bobcat Mini Skid Steer Attachment (35.5″ wide) |
WLD003504 | S14 & S18 ASV & Terex RC30 & PT30 Skid Steer Plate |
WLD001427 | S14 & S18 Bucket Mount Adapter |
WLD001421 | S14 & S18 Weld-On Excavator Adapter |
___________________________________________________________________________________________________________________________________________________________________________________________________
PRICE DOES NOT INCLUDE SETUP OR SHIPPING – PRICED FOB ATWOOD, KS