SM40 Hammer | Universal Skid
Hammer Pictured Above With Optional Grapple
- Loaded With Factory Installed Additional Weight
- 96″ length hoses with flat face couplers
Hydraulic continuous chain drive, 300 lb. hammer weight (500 lbs. max.), 40″ stroke, up to 35 strokes per minute, drives t-post up to railroad ties. Integrated post puller to be used with log chain.
Drives fence posts, sign posts, guard rails, median dividers, tent stakes, T-posts, pipe fence, and railroad ties with ease. Model SM40 has a 40” drop hammer design. With this innovative design, you can achieve a full stroke with every cycle or utilize the short stroke feature to fine tune your depth. The Hammer DOES NOT operate with springs, hydraulic cylinder, or return line. Grapple option can be added to any model for a true one-person operation (does not include t-posts). The grapple option will allow the operator to grab the post off the ground, load it into the machine, and drive it in the ground without leaving the skid-steer seat. Tilt option allows up to 20˚ in each direction. The hammer weight is 300 lbs. from the factory. Additional weight can be added for a total of 500 lbs.
NOTE: If post/pipe diameter is 5″ or smaller and you have a helper, PN 21395 Donut Strike Plate must be purchased separately. If driving with one person, PN 21212 Horseshoe Strike Plate is a better option.
|Post Dimensions:||T-post to RR Tie|
|Impact Force:||82,000 lbs.|
|Length of Stroke:||40|
|Strokes per Minute:||35|
|Model SM40||Model SM40 w/ Grapple|
|Machine Weight||915 lbs (1,115 lbs w/ additional weight)||955 lbs (1,155 lbs w/ additional weight)|
|Hammer Weight||300 LBS (500 LBS MAX)|
|Length of Stroke||40″|
|Max. Strokes per Minute||35|
|Hydraulic Requirements||1500-3000 PSI
|Maximum Post Width||8.5″ x 9.25″|
|Impact Force||82,000 lbs @ 500 lb weight|
|Impact Energy||1,025 ft-lbs @300 lb weight;
1,709 ft-lbs @ 500 lb weight
*Hammer will still operate on machines with less than 12 GPM with fewer strokes per minute.
|DA21220-1||Wiring Harness 8-Pin (Allows tilt function operation from joy stick controls.) Used on ASV, Caterpillar, Komatsu, Terex|
|DA21220-2||Wiring Harness 14-Pin (Allows tilt function operation from joy stick controls.) Used on Bobcat (prior to 1999), Case Kubota, New Holland, Takeuchi, Volvo|
|DA21220-3||Wiring Harness 14-Pin Deere (Allows tilt function operation from joy stick controls.) Used on John Deere|
|DA21220-4||Wiring Harness 14-Pin Caterpillar (Allows tilt function operation from joy stick controls.) Used on Caterpillar|
|DA21220-5||Wiring Harness 14-Pin (Allows tilt function operation from joy stick controls.) Used on Bobcat (1999 and current), Gehl
Bobcat also has a 7-Pin connector on some newer skid steer units that is not available through Danuser, contact your Bobcat dealer for a 7-Pin to 14-Pin adapter.
|DA21220-U1||Wiring Harness 8-Pin (Allows tilt function operation from joy stick controls.) Universal wiring harness. Contacts are crimped on wire, but not installed in connector.*Requires connector contacts be installed in a switchable +12 V pin location and ground pin location.Mapping of skid-steer connector pins required.*|
|DA21220-U2||Wiring Harness 14-Pin (Allows tilt function operation from joy stick controls.) Universal wiring harness. Contacts are crimped on wire, but not installed in connector.*Requires connector contacts be installed in a switchable +12 V pin location and ground pin location. Mapping of skid-steer connector pins required.*|
|DA21253||Wiring Harness that connects to battery (For use with SM40, LM40, or EM40).
This is NOT a complete harness, it replaces the cigarette lighter adapter
|DA186065||Hose Extension Kit
Extends Hammer hoses 24″ when needed on certain skid-steers (e.g. JCB, Volvo).Includes two 24″ hoses and fittings.
|DA21004||SM40 Grapple – May be added to SM40 Hammers Only. Grapple for one-man operation.|
|DA21005||SM40 Tilt – May be added to SM40 Hammers Only. Tilt left or right up to 20 degrees. Includes diverter switch and cigarette lighter adapter that connects to a power port or cigarette lighter inside the cab.|
|DA21149||T-Post Adapter – Must be added for driving t-posts.|
|DA21212||Plate – Floating Horseshoe – Purchase when driving smaller diameter pipe (less than 4″ O.D.) in difficult conditions. Aids in keeping the post centered in the driver and reduces wear and tear on machine. Does not interfere with operation of the grapple. Works with posts 5″ diameter and smaller including “T” post adapter.|
|DA21278||Concrete Breaker Kit – May be added to all Hammer models to convert to a concrete breaker. Breaks up to 9″ thick reinforced concrete. Includes 500 lb. breaker attachment, foot, and additional hardware for assembling.|
|DA21280||Plate – Guard Rail – Recommended when driving 6″ or 8″ I beams. Aids in keeping the guards rail from twisting and shifting. Does NOT work with grapple.|
|DA21395||Plate – 5″ Donut – More effective than the Floating Horseshoe Strike Plate in keeping the pipe centered when driving in difficult conditions. Reduces wear and tear on the machine. Makes grappling of pipe more challenging. Works best when using a helper to position pipe in the Hammer. More pipe fencing professionals prefer the 5″ Donut Strike Plate over the Floating Horseshoe Strike Plate. Works with pipe 4.75″ diameter and smaller. Will work with “T” post adapter.|
|DA21163||Additional Weight Kit – Add steel shot for additional driving force (Up to 60% more power.)|
PRICE DOES NOT INCLUDE SETUP OR SHIPPING – PRICED FOB FACTORY