WFMKX2-130-84XTEND

Open Discharge Spout

• • Reduced horsepower requirements
    • 13” auger = 20% less horsepower required
  • Allows for more efficient flow out of the tube
  • New tapered bearing for increased life span
  • Equipped with plastic hood for sleeker appearance
  • Included on 10”, 13”, and 16” augers

Steerable Axles

• • Improves auger maneuverability around tight corners in transport
  • Improves auger maneuverability when lining auger up to the bin hole
  • Optional on 13-84/94/114
  • Standard on 16” augers

Redesigned Boot

• • Separate boot flight with removable shafts (10”, 13”, and 16”)
  • AR boot flight standard (13” and 16”)
  • Hanger bearing to support boot flight (13” and 16”)
  • Tapered lower bearing for increased life span (13”)
  • Clean-out doors on both sides of the boot (13”)
  • Updated PTO and hose holders (13”)

Transition Neck Flight Support

• • Replaced bushing with self-aligning bearing
    • Longer lasting life-span
  • Splined connection to hopper u-joint provides better alignment and adjustability
  • Included on 13” and 16” augers

30’ Tubes and Flights

• • Less tube flange and flight connections lead to less auger noise
  • Less tube and flight hardware reduces time needed to assemble
  • Common flight and tube lengths leading to less variation to stock
  • Included on 10”, 13”, and 16” augers

13” Truss Updates

• • Simplified truss towers and reduced number of side cable trusses
    • Fewer components/hardware reducing time to assemble

Right Angle Drive

• • Improved gearbox stability
  • Accepts adjustable tow bar
  • New right angle drive with speed reducer
    • Allows auger to be positioned at 90 degree angle from the truck
    • Reduces speed of 1000 RPM tractor to 540 RPM required to run an auger

Auger Lean Prevention

• • Vertical stabilizer brace between lower frame arms to lock and prevent tube from rotating in transport position
  • Stays engaged through lift assist range of motion as auger is raised and then disengages
  • Nylatron GSM material provides a low friction surface to prevent binding
  • Included on MKX² 13” a-frame augers equipped with X-Tend or X-Over swings

Cylinder Updates

• • Commonize cylinders to use with various auger sizes
    • Fewer cylinders required to stock
  • Added ram guide to MKX²1073 cylinder to ensure cylinder lifts straight
  • Change from internal check valve to external check valve
    • Easier to access/service/replace in the field
    • Easier to access/service/replace in the field

MKX2-130 Series 

13″ Diameter | 64′ – 114′ Lengths | Up To 11,000 bph

The MKX2 Series features over 75 proven performance enhancements, specializing in ease-of-use and serviceability. The MKX2 Series is available in 10″, 13″ and 16″ tube diameters and lengths from 53′ to 125′ and capacity up to 23,000 bph.

Smooth & Efficient Operation

The MKX2 Series uses square, one-bolt flight connections to ensure the flighting maintains proper alignment for smooth operation. The upper flight thrust adjuster equalizes the pressure between the upper and lower bearings during operation. This extends the life of the lower boot bearing. The CV PTO reduces vibration and provides maximum power transfer to the auger in order to maintain the life of the unit without sacrificing capacity. The large boot and tapered boot flight maximizes auger capacity at all angles by efficiently channeling grain from the hopper into the auger.

Easy To Service & Maintain

The removable slip-on boot flight uses Wear Edge Technology™ and can be quickly replaced without having to remove and replace the entire lower flight. The MKX2 Series features six easily accessible service points to allow for quick maintenance of u-joints, chains, bearings, and gearboxes. The u-joint end caps have external grease zerks, making it easy to service and maintain. Tool free inspection areas include, the hopper chain cover, neck transition, boot clean-out and swing head cover. The large clean-out, service points, and access panels allow for fast and efficient auger cleaning and servicing.

Trussing + Frame

The MKX2 Series is designed to maintain rigid alignment during heavy loads. Whether it’s heavy-duty cable trussing on smaller units or Westfield’s industry-leading steel trussing on longer, heavier units, the MKX2 withstands bowing to maintain proper tube and flighting alignment making it easier to line the auger up with the bin cap opening. The A-frame undercarriage is built to hold the auger in position and works with wide-standing axles to prevent the auger from swaying or moving once it has been positioned at the bin and the grain starts flowing.

Square Shaft Flighting

The MKX2 Series has square shaft flighting connections with a removable & replaceable boot flight.